RS232 & UART


using a UART (Universal Asynchronous Receiver/Transmitter) for the RS-232 standard. This has to be one of the first communication protocols many of us were introduced to at university or college.

Simply put, RS-232 is a single-ended serial data communication protocol between a DTE (Data Terminal Equipment) and a DCE (Data Circuit-terminating Equipment). So what do these terms actually mean? Well, the DTE is the “master” piece of equipment; for example, your laptop or an ASIC or an FPGA or a microcontroller — whatever is initiating the communications. By comparison, the DCE is the “slave” piece of equipment; for instance, a MODEM back in the days of “dial-up” communications or any other device that is subservient to the main piece of equipment.

RS-232 is one of the oldest communication protocols still in common use. It was originally developed in 1962 which makes it 50 years old this year. The “RS” came from the fact that this was first introduced by the Radio Sector of the Electronic Industries Alliance (EIA), but RS-232 is now generally understood to stand for “Recommended Standard 232.”

The standard itself defines only the physical layer of the protocol — addressing the electrical signal requirements, interface connectors, and so on — but nothing at the data link layer such as framing or error correction.

The complete RS-232 standard defines the signals shown in the table below. However the simplest of RS232 links can be achieved with just three lines — Transmitted Data, Received Data, and Common Ground — with flow control between the DTE and DCE being implemented using commands transmitted over the communications lines (this is often realized using ASCII control characters).

Due to its age, RS-232 uses voltage levels that are considerably higher than those used commonly within designs today. For both transmitted (Tx) and received (Rx) data, the standard defines a logic 1 as a voltage between −3 volts and −15 volts, while a logic 0 is defined as a voltage between +3 volts and +15 volts. For this reason, many designs will contain a transceiver that translates between internal logic levels and the correct RS-232 voltages.

A UART (Universal Asynchronous Receiver/Transmitter) can be used to implement many protocols, with RS-232 being perhaps one of the most common, closely followed by RS-485. Implementing a UART within an FPGA is very simple, requiring only a baud rate generator and a shift register for transmission (with the correct start, parity, and stop bits). Following the start bit, the transmitter transmits the data — LSB (least-significant bit) through to the MSB (most-significant bit) –followed by the parity bit and finally the stop bit(s).

As a small aside, the “stop bit” it is not a real bit, but is instead the minimum period of time the line must be idle at the end of each word. On PCs this period can have three lengths — the time equal to 1, 1.5 or 2 bits.

Implementing a receiver is a little more complicated, because most FPGAs operate at clock frequencies in excess of the RS-232 rate. This allows the receiving FPGA to oversample the incoming receive line. In turn, this allows the leading edge of the start bit to be detected, thereby providing the timing reference for the recovery of the remaining bits. The simplest method is to sample in the middle of the nominal bit period; however, an alternate method of sampling at one third and two thirds of the bit period and confirming that the two sampled values are in agreement is also often used.


The example here is a RS232 receiver this receives an RS-232 signal at 115,200 baud and — in the example provided — the received data is wired out to eight LEDs on my development board allowing them to be turned on or off over the serial link.

Testing this RS-232 Receiver also gave me the opportunity to try out the Oscium LogiScope, which turns your iPad into a very good logic analyzer. In the image below, we see my FPGA development board at the bottom of the image. Behind this board is an iPad. The Oscium LogiScope hardware is the small black box sticking out of the right-hand side of the iPad, while the software (which can be downloaded from the iTunes Store) is running on the iPad.


This enabled me to break out the Rx signal going into the FPGA along with the internal capture register through which the Rx signal is shifted as it is captured. I must say I very impressed with how easy it was to use the LogiScope logic analyzer and set up the triggering etc. since — being a typical engineer — I did not read the user manual. The LogiScope provides the option to perform advanced triggering on patterns or multi-level events, and it also decodes I2C, which will come in useful when we come to discuss that protocol in a future column.

Extracting the screen shots and logs from the iPad was also very simple. Using the email option, it was easy to send these to my email account, thereby allowing me to include them in this blog as shown below:


The beauty of an FPGA-based UART is that it can be easily adapted to interface to other protocols like RS-485 and RS-422. This allows you as the FPGA designer to develop a soft UART core that can be reused across a number of projects. Have you developed such a core — or used someone else’s? If so, please share your experiences with the rest of us.